Meian Only boutique!
.jpg)
News???
Chainsaw use and maintenance of the three issues
2014/4/25??????點擊：
Chainsaws are many products in the garden of the most widely used , one of the highest frequency of use of power tools . Because it comes with a very sharp serrated and used for high-speed cutting of wood , so the use of its operations , the need to adopt more stringent safety precautions. Any non-standard operations, not timely maintenance, will form some security risks , users need to pay attention to. Experts summarize a series of pan use and maintenance tips and precautions to share with readers.
Always ensure that the saw chain lubrication
Saw chain and guide lubrication for the chain saw use , it is extremely important. Technical staff , said the chain has a small amount of lubricating oil must have been thrown out , do not work in the case of the saw chain is not lubricated . If the saw chain run dry , the cutting tool will soon be damaged and can no longer be repaired. So, be sure to check before starting work saw chain lubrication and lubricant oil within the tank .
In order to get the saw chain and guide automatic and reliable lubrication technicians recommend the use of high-quality, environmental pollution and guides the saw chain lubricants, such as anti-aging ability , readily biodegradable lubricants. If a low resistance to aging , oil gelling easy , difficult to form a hard to remove the precipitate , especially in the saw chain drive , the clutch and the chain around , and in severe jammed the pump. In addition, the non- use of waste oil . Waste lubricating oil does not have the capacity required , and many contacts waste lubricating oil may cause skin cancer , waste oil will damage the environment.
It will be added over time plus fuel oil each chain , must , must ensure that every time you run out of fuel , lubricating oil inside the chain there is a little residual oil . If the lubricant oil tank is not reduced in case there may be caused due to the clogging of the lubricating oil passage . This time to check the saw chain lubrication. Cleaning the oil , if necessary, seek help from your service provider .
For new factory machinery , run-in period to avoid unnecessarily high load operation , therefore , before the fuel runs out do the first three boxes for high-speed idling. As the moving parts must , subject to mutual accommodation in the run-in period , so in the meantime a short cylinder has a larger friction . Engine runs at about 5-is the oil tank after reaching its maximum power . Chainsaws during normal operation , do not adjust the oil mix ratio is too low to significantly increase the power , 'This could damage the engine .
In addition , we should always check the saw chain tension . Compared with the already cast a long time people use chain saws , chain saws require new and more frequent tighten . Usually in the cold state , the chain guide plate side furans in the aggregate but still able to pull his hand along the guide , Tony explained tension is correct. After reaching operating temperature, chain saws expansion began to relax . Do not allow the drive chain guide plate from the lower section of the guide slot , otherwise the chain will fall off . Tighten the chain again if necessary. When cool , chain saws will shrink . This time to loosen the chain , otherwise it will damage the crankshaft and bearings.
Chainsaws use mo attention to detail
Oil
Saw in use
Process, there are a few users need to pay particular attention to the operational details . First of all, when you start Chainsaws , Mo will start hove to end. Light from the start when you start the hand grip , until the stop , then quickly pulling force , while pressing down the front handle . Technical staff said , should not completely pull the starter rope to the floor , otherwise might pull it off . Said often used , users often do not pay attention to this detail , over time , start the rope easily damaged. Also note , do not let the freedom to start playing back the handle , it should slowly back into the chassis so that the rope can be a good starting roll up .
Next, after the long-term operation of the engine to full throttle , the idle time required to operate , so that the cooling air flow , release of most of the heat engine . This will avoid installing in part on the engine ( ignition , carburetor ) appear Heat
Again, if the engine power is decreased , the air filter may be dirty . Remove the carburetor cover , remove the air filter , remove dirt around the filter , the filter section and two separate clean dust filter with the palm , or blown clean with compressed air from the inside out .
If the filter is stuck dirt , you need to put a filter on a dedicated cleaner or a clean , non- flammable _ lotion inside ( eg warm soapy water ) wash and dry . Do not use a brush to clean the wool over bismuth device .
When you reinstall the air filter , remember to check the dampers and torsion location is correct.
To timely and thorough post- maintenance
Chainsaw maintenance, the most important is that the saw chain. Proper maintenance and sharpening the saw chain can easily It only minimal pressure into the wood. When routine maintenance, pay attention to check whether there are cracks and broken on the saw chain rivet ruthenium section . Replace any damage or worn parts on chain saws , and with the same shape and size as the original new parts. Carbide saw chain is particularly resistant to wear.
Saw chain sharpening work can usually be done by a service dealer . Must maintain a skirt tooth sharpening angle . All jagged angles must be the same , if different, the saw will not turn smoothly , and badly worn until the saw -strand breaks . Length must be the same for all jagged . If different , tooth height will be different , it will also cause the saw chain rotation is not smooth and eventually rupture. After sharpening the saw chain to thoroughly clean , clean attached . Above setback ^ or dust and lubricate According chain. If a long time, the need to ensure the saw chain in the well-oiled state storage.
For long-term storage chainsaw is ' to the fuel in a well ventilated place.
Always ensure that the saw chain lubrication
Saw chain and guide lubrication for the chain saw use , it is extremely important. Technical staff , said the chain has a small amount of lubricating oil must have been thrown out , do not work in the case of the saw chain is not lubricated . If the saw chain run dry , the cutting tool will soon be damaged and can no longer be repaired. So, be sure to check before starting work saw chain lubrication and lubricant oil within the tank .
In order to get the saw chain and guide automatic and reliable lubrication technicians recommend the use of high-quality, environmental pollution and guides the saw chain lubricants, such as anti-aging ability , readily biodegradable lubricants. If a low resistance to aging , oil gelling easy , difficult to form a hard to remove the precipitate , especially in the saw chain drive , the clutch and the chain around , and in severe jammed the pump. In addition, the non- use of waste oil . Waste lubricating oil does not have the capacity required , and many contacts waste lubricating oil may cause skin cancer , waste oil will damage the environment.
It will be added over time plus fuel oil each chain , must , must ensure that every time you run out of fuel , lubricating oil inside the chain there is a little residual oil . If the lubricant oil tank is not reduced in case there may be caused due to the clogging of the lubricating oil passage . This time to check the saw chain lubrication. Cleaning the oil , if necessary, seek help from your service provider .
For new factory machinery , run-in period to avoid unnecessarily high load operation , therefore , before the fuel runs out do the first three boxes for high-speed idling. As the moving parts must , subject to mutual accommodation in the run-in period , so in the meantime a short cylinder has a larger friction . Engine runs at about 5-is the oil tank after reaching its maximum power . Chainsaws during normal operation , do not adjust the oil mix ratio is too low to significantly increase the power , 'This could damage the engine .
In addition , we should always check the saw chain tension . Compared with the already cast a long time people use chain saws , chain saws require new and more frequent tighten . Usually in the cold state , the chain guide plate side furans in the aggregate but still able to pull his hand along the guide , Tony explained tension is correct. After reaching operating temperature, chain saws expansion began to relax . Do not allow the drive chain guide plate from the lower section of the guide slot , otherwise the chain will fall off . Tighten the chain again if necessary. When cool , chain saws will shrink . This time to loosen the chain , otherwise it will damage the crankshaft and bearings.
Chainsaws use mo attention to detail
Oil
Saw in use
Process, there are a few users need to pay particular attention to the operational details . First of all, when you start Chainsaws , Mo will start hove to end. Light from the start when you start the hand grip , until the stop , then quickly pulling force , while pressing down the front handle . Technical staff said , should not completely pull the starter rope to the floor , otherwise might pull it off . Said often used , users often do not pay attention to this detail , over time , start the rope easily damaged. Also note , do not let the freedom to start playing back the handle , it should slowly back into the chassis so that the rope can be a good starting roll up .
Next, after the long-term operation of the engine to full throttle , the idle time required to operate , so that the cooling air flow , release of most of the heat engine . This will avoid installing in part on the engine ( ignition , carburetor ) appear Heat
Again, if the engine power is decreased , the air filter may be dirty . Remove the carburetor cover , remove the air filter , remove dirt around the filter , the filter section and two separate clean dust filter with the palm , or blown clean with compressed air from the inside out .
If the filter is stuck dirt , you need to put a filter on a dedicated cleaner or a clean , non- flammable _ lotion inside ( eg warm soapy water ) wash and dry . Do not use a brush to clean the wool over bismuth device .
When you reinstall the air filter , remember to check the dampers and torsion location is correct.
To timely and thorough post- maintenance
Chainsaw maintenance, the most important is that the saw chain. Proper maintenance and sharpening the saw chain can easily It only minimal pressure into the wood. When routine maintenance, pay attention to check whether there are cracks and broken on the saw chain rivet ruthenium section . Replace any damage or worn parts on chain saws , and with the same shape and size as the original new parts. Carbide saw chain is particularly resistant to wear.
Saw chain sharpening work can usually be done by a service dealer . Must maintain a skirt tooth sharpening angle . All jagged angles must be the same , if different, the saw will not turn smoothly , and badly worn until the saw -strand breaks . Length must be the same for all jagged . If different , tooth height will be different , it will also cause the saw chain rotation is not smooth and eventually rupture. After sharpening the saw chain to thoroughly clean , clean attached . Above setback ^ or dust and lubricate According chain. If a long time, the need to ensure the saw chain in the well-oiled state storage.
For long-term storage chainsaw is ' to the fuel in a well ventilated place.
- Pre： //
- Next：Chainsaws purposes 2014/4/25
